manualshive.com logo in svg

YASKAWA SI-ES3, Техническое руководство, Страница: 15 / 62

Поделиться
Скачать
YASKAWA SI-ES3 Скачать руководство пользователя страница 15

5  Installation Procedure

YASKAWA ELECTRIC

 SIEP C730600 64A 1000-Series Option SI-ES3  Technical Manual

 15

5.

Route the option wiring.
Depending on the drive model, some drives may require routing the wiring through the side of the front cover to 
the outside to provide adequate space for the wiring. Refer to the Peripheral Devices & Options section of the 
drive Quick Start Guide or Technical Manual for more information on wire routing of specific models.

Route the wiring through the side of the front cover to the outside. In these cases, using diagonal cutting pliers, 
cut out the perforated openings on the left side of the drive front cover as shown in 

Figure 9

-A. Sharp edges 

along the cut out should be smoothed down with a file or sand paper to prevent any damage to the wires.
Route the wiring inside the enclosure as shown in 

Figure 9

-B for drives that do not require routing through the 

front cover.

Note:

Separate communication cables from main circuit wiring and other electrical lines.

Figure 9  

Figure 9  Wire Routing Examples

6.

Connect the EtherCAT communication cable to the option modular connector CN1 and CN2. 
To connect the option to a network, insert the RJ45 communication connector of the Cat5e patch cable into the 
option modular female connector CN1 and CN2. Ensure the cable end is firmly connected (see 

Figure 9

).

Communication Cable Specifications

Only use cable recommended for EtherCAT. Using a cable not specifically recommended may cause the option 
or drive to malfunction.

Connection Diagram

Figure 10  Option Connection Diagram

A – Route wires through the openings provided 

on the left side of the front cover. 

<1>

<1> The drive will not meet NEMA Type 1 requirements if wiring is exposed outside the enclosure.

B – Use the open space provided inside the drive 

to route option wiring.

<1>  The ground wire provided in the option shipping package must be connected during installation.

B

A

A1000

Drive

M

U

V

W

R

S

T

CN5-A

FE

<1>

EtherCAT Master

EtherCAT Cable

Motor

Power

SI-ES3

EtherCAT

Option

CN1, 
CN2

A1000

Содержание SI-ES3































































Отзывы:

Нет отзывов