YASKAWA SI-ES3 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 62

YASKAWA SI-ES3 Скачать руководство пользователя страница 13

5 Installation Procedure

YASKAWA ELECTRIC

SIEP C730600 64A 1000-Series Option SI-ES3 Technical Manual

13

Installing the Option

Remove the front covers of the drive before installing the option. Refer to the drive Quick Start Guide for directions on
removing the front covers. Cover removal varies depending on drive size. This option can be inserted only into the

CN5-A

connector located on the drive control board.

WARNING!

Electrical Shock Hazard. Do not connect or disconnect wiring while the power is on. Failure to comply could result in death

or serious injury. Before installing the option, disconnect all power to the drive and wait at least the amount of time specified on the
drive front cover safety label. After all indicators are off, measure the DC bus voltage to confirm safe level, and check for unsafe
voltages before servicing. The internal capacitor remains charged after the power supply is turned off.

1.

Shut off power to the drive, wait the appropriate amount of time for voltage to dissipate, then remove the digital
operator (D) and front covers (C, F). Refer to the Quick Start Guide packaged with the drive for directions on
removing the front covers. Cover removal varies depending on drive size.

NOTICE:

Damage to Equipment. Observe proper electrostatic discharge procedures (ESD) when handling the option, drive, and

circuit boards. Failure to comply may result in ESD damage to circuitry.

Figure 5

Figure 5 Remove the Front Covers and Digital Operator

2.

With the front covers and digital operator removed, apply the LED label (E) in the appropriate position on the
drive top front cover (C).

Figure 6

Figure 6 Apply the LED Label

C

D

F

A1000

RUN

ERR

L/A IN

L/A OUT

C

E

A1000

«
...
11
12
13
14
15
...
»

Содержание SI-ES3































































Отзывы:

Нет отзывов