YASKAWA SI-ES3 Скачать руководство пользователя страница 57

Страница: 57 / 62

12 Fault Diagnosis and Possible Solutions

YASKAWA ELECTRIC

SIEP C730600 64A 1000-Series Option SI-ES3 Technical Manual

LED Operator Display

Fault Name

oFA01

Option Card Fault (CN5-A)

Option is not properly connected.

Cause

Possible Solution

Problem with the connectors between the drive
and option

Turn the power off and check the connectors between the drive and option.

LED Operator Display

Fault Name

oFA30 to oFA43

Option Card Connection Error (CN5-A)

Communication ID error

Cause

Possible Solution

Option hardware fault

Replace the option.

LED Operator Display

Fault Name

oFb00

Option Fault (CN5-B)

Non-compatible option is connected.

Cause

Possible Solution

Non-compatible option connected to the drive.

Connect the correct option to CN5-A.

LED Operator Display

Fault Name

oFb02

Option Fault (CN5-B)

Two identical options are connected at the same time.

Cause

Possible Solution

Options AI-A3 or DI-A3 are connected to the
CN5-B port with an option connected to CN5-A.

• Only one type of AI-A3, DI-A3 or SI-

option can be connected to the drive.

• The SI-ES3 option can only be connected to CN5-A.

LED Operator Display

Fault Name

oFC00

Option Fault (CN5-C)

Non-compatible option is connected.

Cause

Possible Solution

Non-compatible option connected to the drive.

Connect the correct option to CN5-A.

LED Operator Display

Fault Name

oFC02

Option Fault

Option Flash write mode

Cause

Possible Solution

Options AI-A3 or DI-A3 are connected to the
CN5-B port while an option connected to
CN5-A.

• Only one type of AI-A3, DI-A3 or SI-

option can be connected to the drive.

• The SI-ES3 option can only be connected to CN5-A.

Содержание SI-ES3































































Результаты поиска

Содержание SI-ES3

Отзывы:

YASKAWA SI-ES3, Техническое руководство, Страница: 57 / 62

Результаты поиска

Содержание SI-ES3

Отзывы: