YASKAWA SI-ES3 Скачать руководство пользователя страница 38

Страница: 38 / 62

8 Object Dictionary

YASKAWA ELECTRIC

SIEP C730600 64A 1000-Series Option SI-ES3 Technical Manual

2200 (Hex) - Motor Speed

This object can be used to monitor the motor speed. The value in object 2200 (Hex) is not filtered. Setting units are
determined by o1-03.

The availability of the object content depends on the drive control mode. If the selected control mode does not support
this monitor (equal to drive monitor U1-05), the object value will be 0. Refer to the drive technical manual for details.

2210 (Hex) - DC Bus Voltage

This object can be used to monitor the DC bus voltage.

2220 (Hex) - Analog Input Monitor A1

This object can be used to display the analog input A1 level; 100% when input is 10 V.

2240 (Hex) - Analog Input Monitor A2

This object can be used to display the analog input A2 level; 100% when input is 10 V.

Index

(Hex)

Subindex

Content

Default

Access

PDO

Mapping

Value Range

2200

–

Motor speed

–

Read Only

–

Number of entries

–

Read Only

Unsigned 8

Motor speed

–

Read Only

Unsigned 16

MEMOBUS/Modbus register address of

content

0044 (Hex)

Read Only

Unsigned 16

Value (MEMOBUS/Modbus register): 0x0044 (Motor speed)

Index

(Hex)

Subindex

Content

Default

Access

PDO

Mapping

Value Range

2210

–

DC bus voltage

–

Read Only

–

Value

1 V

Read Only

Unsigned 16

MEMOBUS/Modbus register address of

content

0046 (Hex)

Read Only

Unsigned 16

Value (MEMOBUS/Modbus register): 0x0046 (DC Bus voltage)

Index

(Hex)

Subindex

Content

Default

Access

PDO

Mapping

Value Range

2220

–

Analog input monitor A1

–

Read Only

–

Value

0.1%

Read Only

Unsigned 16

MEMOBUS/Modbus register address of

content

004E (Hex)

Read Only

Unsigned 16

Value (MEMOBUS/Modbus register): 0x004E (Terminal A1 Input Level)

Index

(Hex)

Subindex

Content

Default

Access

PDO

Mapping

Value Range

2240

–

Analog input monitor A2

–

Read Only

–

Value

0.1%

Read Only

Unsigned 16

MEMOBUS/Modbus register address of

content

004F (Hex)

Read Only

Unsigned 16

Value (MEMOBUS/Modbus register): 0x004F (Terminal A2 Input Level)

Содержание SI-ES3































































Результаты поиска

Содержание SI-ES3

Отзывы:

YASKAWA SI-ES3, Техническое руководство, Страница: 38 / 62

Результаты поиска

Содержание SI-ES3

Отзывы: