YASKAWA SI-ES3 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 62

YASKAWA SI-ES3 Скачать руководство пользователя страница 43

8 Object Dictionary

YASKAWA ELECTRIC

SIEP C730600 64A 1000-Series Option SI-ES3 Technical Manual

43

604C (Hex) - vl Dimension Factor

The vl dimension factor is multiplied with the target velocity. The quotient of the subindexes vl dimension factor
numerator and vl dimension factor denominator determines the vl dimension factor.

Default Value = 1

This parameter affects other objects such as:

• 0x6042 vl_target_velocity
• 0x6043 vl_velocity_demand
• 0x6044 vl_velocity_actual_value
• 0x6046 vl_velocity_min_max_amount
• 0x6048 vl_velocity_acceleration
• 0x6049 vl_velocity_deceleration
• 0x604A vl_velocity_quick_stop

and is always used in a product.

604D (Hex) - vl Pole Number

The vl pole number sets the number of motor poles and is used to calculate all speed related values in r/min. This value
corresponds to the number of motor poles setting in the drive.

MEMOBUS/Modbus register: 0x0311, E2-04 (Number of motor poles)

6060 (Hex) - Modes of Operation

This object sets the mode of the device. The object supports 2 (Velocity Mode) only.

Value: 2: Velocity mode

6061 (Hex) - Modes of Operation Display

This object shows the mode of the device. The object supports 2 (Velocity Mode) only.

Value: 2: Velocity mode

Value: -2: Vendor specific mode

Index (Hex)

Subindex

Content

Access

PDO Mapping

Value Range

604C

1

vl dimension factor numerator

Read/Write

Rx/Tx

-2

31

...(2

31

-1)

Internal in EtherCAT option card, save in NVS memory.
Default Value = 1

2

vl dimension factor denominator

Read/Write

Rx/Tx

-2

31

...(2

31

-1)

Internal in EtherCAT option card, save in NVS memory.
Default Value = 1

Index (Hex)

Subindex

Content

Access

PDO Mapping

Value Range

604D

0

vl pole number

Read/Write

Tx

0...255

Index (Hex)

Subindex

Content

Access

PDO Mapping

Value Range

6060

0

Modes of operation

Read/Write

Rx/Tx

-128...127

Index (Hex)

Subindex

Content

Access

PDO Mapping

Value Range

6061

0

Modes of operation display

Read Only

Tx

-128...127

«
...
41
42
43
44
45
...
»

Содержание SI-ES3































































Отзывы:

Нет отзывов