manualshive.com logo in svg

YASKAWA SI-ES3, Техническое руководство, Страница: 58 / 62

Поделиться
Скачать
YASKAWA SI-ES3 Скачать руководство пользователя страница 58

12  Fault Diagnosis and Possible Solutions

58

 

YASKAWA ELECTRIC

 SIEP C730600 64A 1000-Series Option SI-ES3  Technical Manual

„

Option Error Management

This section describes the errors managed by the option and the linked actions taken.

Table 24  Option Error Management

Option Error

Description

Error Indication

Possible Solution

OP

→

SAFEOP/PREOP

when drive running

When an EtherCAT state transition from 

OP

→

SAFEOP/PREOP was made when 

the drive was in OPERATION enabled.

bUS Error is triggered in drive.

Note:

 Error against drive will be 

cleared when the next lower to 
higher EtherCAT state transition 
is made.

Check and correct state machine 
transitions in Controlword.

OP

→

SAFEOP

EtherCAT WD time out

If the EtherCAT watchdog time out is 
enabled (Default in ESI file) and output 
data from PLC to the drive is not updated 
in time, an error will be triggered.

bUS Error is triggered in drive.

Note:

 Error against drive will be 

cleared when the next lower to 
higher EtherCAT state transition 
is made.

• Check network connection (e.g. if 

cables plugged in at each node).

• Check telegram timing. Are 

telegrams sent to the slave the error 
occurred on?

OP

→

SAFEOP

1. Drive frame check 

sequence error

2. Drive COMID error

1. Drive has detected a Sum check error.
2. Drive has detected a Communication 
Option ID error.
Possible cause:
1. Option card is overloaded.
2. Option is not properly processing the 
state.

1. Drive fault: oF

†

32

2. Drive fault: oF

†

30

• Disable process data OUT sync 

manager channel.

• Force EtherCAT state change to 

SAFEOP.

OP

→

SAFEOP

1. Option card frame check 

sequence error

2. Option card COMID error

1. Option card has detected a Sum check 
error.
2. Option card has detected a 
Communication Option card ID error.
Possible cause: 
1. Drive system is overloaded.
2. Drive is not properly processing the 
state.

1. Drive fault: oF

†

32

2. Drive fault: oF

†

30

• Disable process data IN sync 

manager channel.

• Force EtherCAT state change to 

SAFEOP.

Initial power-up sequence not 
completed within 10 seconds.

Possible cause:
Drive is not processing the internal 
interface protocol.
Drive does not support EtherCAT option 
card.

Drive fault: oF

†

00

Option will log FATAL event 
record in NVS memory and set 
ERR LED: solid RED, see 

Table 4

.

• Check drive firmware version.
• If drive firmware version is correct, 

replace option card.

• Replace the drive.

 I/F proc time out

Option card has not processed any drive 
system frames in 1000 ms.
Possible cause:
Drive has stopped serving the internal 
interface to option card or HW failure.

Option will log FATAL event 
record in NVS memory, and set 
ERR LED: solid RED, see 

Table 4

.

Force EtherCAT state to INIT.

Option ID Error: Power-up 

sequence copyright string 

mismatch.

Drive reported invalid copyright string in 
power-up process.

Option will log FATAL event 
record in NVS memory, and set 
ERR LED: solid RED, see 

Table 4

.

Replace option card.

Содержание SI-ES3































































Отзывы:

Нет отзывов