Wood-mizer LT15WB D17 страница 78 Скачать руководство пользователя | Manualshive

Страница: 78 / 88

background image

Sawmill Alignment

Blade Guide Installation

5

5-14

1510doc071918

Sawmill Alignment

See Figure 5-16.

Use the horizontal adjustment screws to adjust the drive-side blade wheel.

To move the blade back on the wheel, loosen the right adjustment screw one quarter turn.
Loosen the jam nut on the left adjustment screw and tighten the screw. Tighten the left and right
jam nuts.

To move the blade out on the wheel, loosen the left adjustment screw one quarter turn. Loosen
the jam nut on the right adjustment screw and tighten the screw. Tighten the left and right jam
nuts.

Blade Guide Installation

Each Wood-Mizer sawmill has two blade guide assemblies that help the blade maintain a straight
cut. The two blade guide assemblies are positioned on the saw head to guide the blade on each
side of the material being cut.

One blade guide assembly is mounted in a stationary position on the drive side of the saw head.
This assembly is referred to as the "inner" blade guide assembly.

The other blade guide assembly is mounted on the idle side of the saw head. It is referred to as
the "outer" assembly and is adjustable for various widths of materials to be processed.

NOTE:

Before installing the blade guide assemblies, remove the blade guide

adjusting screws and apply a lubricating oil such as 10W30 or Dexron III to
each screw. This will prevent the screws and threaded holes from corroding
and make screw adjustments easier.

1.

Install the outer blade guide assembly (with waterlube tube) to the mounting block on the blade
guide arm. Position the assembly so the roller flange is 1/8" (3.0 mm) from the blade.

2.

Install the inner blade guide assembly to the mounting block on the saw head. Position the
assembly so the roller flange is 1/16" (1.5 mm) from the blade.

FIG. 5-16

150210-15

Adjust horizontal adjustment screws

left to move blade out on wheel;

Adjust screws right to move blade in on wheel

«
...
76
77
78
79
80
...
»

Содержание LT15WB D17

























































































Отзывы:

Нет отзывов

Похожие инструкции для LT15WB D17

Бренд: Cobra Страницы: 10

Бренд: ZIPPER MASCHINEN Страницы: 109

Brave EZ Split PCLS04

Бренд: Brave Страницы: 35

Бренд: Sami autochopper Страницы: 43

Power Force KCG-20LS

Бренд: King Canada Страницы: 14

Бренд: Scheppach Страницы: 36

Бренд: Scheppach Страницы: 352

Бренд: Asist Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды