Wood-mizer LT15WB D17 Скачать руководство пользователя страница 77

Страница: 77 / 88

Sawmill Alignment

Blade Wheel Alignment

Sawmill Alignment

1510doc071918

5-13

See Figure 5-14.

The horizontal tilt of the blade wheel should be adjusted so that the gullet of an

1-1/4" blade is 1/8" (3 mm) out from the front edge of the wheel (±1/32 [0.75 mm]).

See Figure 5-15.

Use the cant control adjustment to adjust the idle-side blade wheel. If the blade

is too far forward on the wheel, turn the cant control counterclockwise. If it is too far back on the
wheel, turn the cant control clockwise.

10.

Check the position of the blade on the drive-side blade wheel. The blade should be positioned on
the wheel as described for the idle-side blade wheel. Adjust the drive-side blade wheel if neces-
sary.

FIG. 5-14

FIG. 5-15

1 1/4"

Blade

± 1 mm (3/64”)

3.0 mm (1/8”)

150210-10

Cant Control

Содержание LT15WB D17

























































































Результаты поиска

Содержание LT15WB D17

Отзывы:

Бренды по названию

Популярные бренды

Wood-mizer LT15WB D17, Инструкция по безопасности, установке, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание LT15WB D17

Отзывы:

Бренды по названию

Популярные бренды