Wood-mizer LT15WB D17 страница 19 Скачать руководство пользователя | Manualshive

Страница: 19 / 88

background image

Safety & General Information

Safety Instructions

Safety & General Information

doc071918

1-5

1

1.5

Safety Instructions

IMPORTANT!

The sawmill is intended for sawing wood only.

The sawmill must not be used for other purposes such as cutting ice,
metal or any other materials.

See Section 5.2

for log size capacities of

the machine.

IMPORTANT!

The operator of the sawmill should get adequate

training in the operation and adjustment of the machine.

NOTE:

ONLY safety instructions regarding personal injury are listed in this section. Caution

statements regarding only equipment damage appear where applicable throughout the manual.

Observe Safety Instructions

IMPORTANT!

Read the entire Operator's Manual before operating the

sawmill. Take notice of all safety warnings throughout this manual and
those posted on the machine. Keep this manual with this machine at all
times, regardless of ownership.

Also read any additional manufacturer’s manuals and observe any
applicable safety instructions including dangers, warnings, and
cautions.

Only adult persons who have read and understood the entire
operator's manual should operate the sawmill. The sawmill is not
intended for use by or around children.

IMPORTANT!

It is always the owner's responsibility to comply with all

applicable  federal,  state  and  local  laws,  rules  and  regulations
regarding the ownership and operation of your Wood-Mizer sawmill. All
Wood-Mizer  sawmill  owners  are  encouraged  to  become  thoroughly
familiar  with  these  applicable  laws  and  comply  with  them  fully  while
using the machine.

!

!

«
...
17
18
19
20
21
...
»

Содержание LT15WB D17

























































































Отзывы:

Нет отзывов

Похожие инструкции для LT15WB D17

Бренд: Hakki Pilke Страницы: 42

Бренд: Central Machinery Страницы: 11

Бренд: Central Machinery Страницы: 12

Бренд: Central Machinery Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды