Wood-mizer LT15WB D17 Скачать руководство пользователя

Страница: 64 / 88

Troubleshooting Guide

Sawing Problems

4-2

1510doc071918

Troubleshooting Guide

PROBLEM

CAUSE

SOLUTION

Boards Thick Or Thin On Ends
Or Middle Of Board.

Stress in log which causes log
to not lay flat on the bed.

After log has been squared, take
equal cuts off opposing sides. Take a
board off the top. Turn the log 180
degrees. Take a board off. Repeat,
keeping the heart in the middle of the
cant, and making it your last cut.

Set in teeth.

Resharpen and reset blade.

Bed rails misaligned.

Realign sawmill.

Height Adjustment Jumps or
Stutters When Moving Up or
Down.

Up/down chain improperly
adjusted.

Adjust up/down chain.

Vertical wear pads are too tight. Adjust pads.

Lumber Is Not Square

Vertical side supports not
square to bed

Adjust side supports.

Blade not parallel to bed rails

Adjust bed rails parallel to blade.

Sawdust or bark between cant
and bed rails

Remove particles

Tooth set problems

Resharpen and reset blade

Sawdust Builds Up On Track

Excessive oiling

Do not oil track

Track wipers worn

Adjust wipers to firmly contact track

Track is sticky

Clean track with solvent and apply sil-
icone spray

Wavy Cuts

Excessive feed

Slow feed rate

Improperly sharpened blade
(This will be the problem 99%
of the time!)

Resharpen blade, following the sharp-
ener’s instructions carefully

Blade guides improperly
adjusted

Adjust blade guides.

Sap buildup on blade

Use Water Lube.

Tooth set problem

Resharpen and reset blade

Содержание LT15WB D17

























































































Результаты поиска

Содержание LT15WB D17

Отзывы:

Похожие инструкции для LT15WB D17

Бренды по названию

Популярные бренды

Wood-mizer LT15WB D17, Инструкция по безопасности, установке, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание LT15WB D17

Отзывы:

Похожие инструкции для LT15WB D17

Бренды по названию

Популярные бренды