Wood-mizer LT15WB D17 Скачать руководство пользователя | Manualshive

Страница: 69 / 88

background image

Sawmill Alignment

Blade Guide Horizontal Tilt Adjustment

Sawmill Alignment

1510doc071918

5-5

5

See Figure 5-4.

3.

Move the carriage so that the front end of the tool is positioned above the bed rail. Measure the
distance from the bed rail to the bottom edge of the tool.

4.

Move the carriage so that the back end of the tool is positioned above the bed rail. Measure the
distance from the bed rail to the bottom edge of the tool.

5.

If the measurement from the tool to the bed rail is not equal within 1/32" (.75 mm), adjust the ver-
tical tilt of the outer blade guide roller.

6.

Loosen one set screw at the side of the blade guide assembly.

See Figure 5-5.

Loosen the jam nuts on the top and bottom vertical tilt adjustment screws. To tilt

the roller up, loosen the bottom screw and tighten top screw. To tilt the roller down, loosen the top
screw and tighten the bottom screw. Tighten the jam nuts and recheck the tilt of the blade.

7.

Move the blade guide alignment tool close to the inner blade guide roller assembly and repeat
the above steps. Adjust the vertical tilt of the inner blade guide if necessary.

Blade Guide Horizontal Tilt Adjustment

If the blade guides are tilted in the wrong direction horizontally, the back of the blade may contact
the flange as the roller is spinning down, causing it to push the blade away from the guide roller.

8.

Remove the blade guide alignment tool from the blade and adjust the blade guide arm halfway in.

FIG. 5-4

FIG. 5-5

SM0310-1

Adjust screws down
to tilt roller up; Adjust
screws up to tilt roller
down

Bottom Vertical Tilt
Adjustment Screw

Top Vertical Tilt
Adjustment Screw

«
...
67
68
69
70
71
...
»

Содержание LT15WB D17

























































































Отзывы:

Нет отзывов

Похожие инструкции для LT15WB D17

Бренд: Zipper Mowers Страницы: 45

Бренд: ZIPPER MASCHINEN Страницы: 82

Бренд: Vito Agro Страницы: 56

Бренд: Greyhound Страницы: 12

Бренд: P.Lindberg Страницы: 50

FB1500-5TEG52STAND

Бренд: Elem Garden Technic Страницы: 13

Бренд: SPLIT SECOND Страницы: 20

Бренд: Range Road Страницы: 14

Бренд: Bushranger Страницы: 28

Бренд: Woodtec Страницы: 36

Бренд: IKH Страницы: 34

Бренд: IKH Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды