Wood-mizer LT15WB D17 Скачать руководство пользователя | Manualshive

Страница: 68 / 88

background image

Sawmill Alignment

Blade Guide Vertical Tilt Alignment

5

5-4

1510doc071918

Sawmill Alignment

See Figure 5-3.

With the blade guide arm still all the way in toward the other blade guide, tighten

all the side screws until they touch the arm. Back the screws off 1/4 turn and tighten the jam nuts.

4.

Measure the distance between the blade guide arm and back edge of the blade. Adjust the
appropriate side screws on the blade guide arm housing so the arm is measures the same dis-
tance from the blade at both ends of the arm.

5.

To move the blade guide end of the arm toward the front of the sawmill, loosen jam nuts on the
front inside screw and the rear outside screw. Turn the screws counterclockwise one full turn and
tighten the jam nuts. Loosen the jam nuts on the front outside screw and the rear inside screw.
Turn the screws clockwise until they touch the arm, back off 1/4” turn, and tighten the jam nuts.

6.

To move the blade guide end of the arm toward the rear of the sawmill, loosen jam nuts on the
front outside screw and the rear inside screw. Turn the screws counterclockwise one full turn and
tighten the jam nuts. Loosen the jam nuts on the front inside screw and the rear outside screw.
Turn the screws clockwise until they touch the arm, back off 1/4” turn, and tighten the jam nuts.

Blade Guide Vertical Tilt Alignment

The blade guides should be adjusted properly in the vertical plane. If the blade guides are tilted
vertically, the blade will try to travel in the tilted direction.

A Blade Guide Alignment Tool (BGAT) is provided to help you measure the vertical tilt of the
blade.

1.

Open the adjustable blade guide arm 1/2" (13 mm) from full open.

2.

Clip the alignment tool on the blade. Position the tool close to the outer blade guide assembly. Be
sure the tool does not rest on a tooth or burr, and is lying flat against the bottom of the blade.

FIG. 5-3

Blade Guide Arm Parallel to Blade

Adjust side screws to

change arm angle

150036B

«
...
66
67
68
69
70
...
»

Содержание LT15WB D17

























































































Отзывы:

Нет отзывов

Похожие инструкции для LT15WB D17

6-TON ELECTRIC WOOD SPLITTER

Бренд: DR Страницы: 34

Бренд: P.Lindberg Страницы: 42

Бренд: PAPILLON Страницы: 18

Бренд: PAPILLON Страницы: 18

Бренд: BE Power Equipment Страницы: 11

Бренд: Talon Страницы: 7

Бренд: Strend Pro Страницы: 36

Hakki Pilke 1x37 Combi

Бренд: Maaselan Kone Oy Страницы: 57

Бренд: Ryobi Страницы: 14

Бренд: Ryobi Страницы: 16

Бренд: KENTMASTER Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды