Wood-mizer LT15WB D17 страница 57 Скачать руководство пользователя | Manualshive

Страница: 57 / 88

background image

Maintenance

Drive Belt Adjustment

Maintenance

doc071918

3-5

3

ADJUST THE DRIVE BELT TENSION

1.

Loosen the drive belt jam and hex nuts. Turn the jam nut counterclockwise (as viewed from the
top) to tighten the belt.

See Figure 3-2.

2. GAS OPTION ONLY:

After tensioning the drive belt, check the throttle linkage and adjust if nec-

essary.

NOTE:

With the clutch handle engaged, the throttle linkage should move the throttle lever to full

speed. To adjust, loosen the throttle linkage adjustment screw and slide the throttle linkage down.
Retighten the screw.

Periodically check the drive belt for wear. Replace any damaged or worn belts as needed.

ADJUST THE DRIVE BELT SUPPORT

The drive belt support is designed to extend belt life. The bracket should be adjusted to NOT
touch the drive belt when the clutch handle is engaged (down position), AND to hold the drive
belt away from the engine pulley when the clutch handle is disengaged (up position).

FIG. 3-2

150210-13C

1/2“ (13 mm)

Turn jam nut clockwise

to loosen drive belt

Throttle Linkage

Adjustment

Belt Tension Gauge

Hex Nut

After 4/15

AR

«
...
55
56
57
58
59
...
»

Содержание LT15WB D17

























































































Отзывы:

Нет отзывов

Похожие инструкции для LT15WB D17

6-TON ELECTRIC WOOD SPLITTER

Бренд: DR Страницы: 34

Бренд: Yardworks Страницы: 65

Бренд: Yard-Man Страницы: 16

Бренд: Echo Страницы: 1

Garden Tools RD-LGS02

Бренд: Raider Страницы: 32

Бренд: Troy-Bilt Страницы: 36

Бренд: power King Страницы: 11

Бренд: power King Страницы: 14

Бренд: Northern Industrial Tools Страницы: 36

22 TON LOG SPLITTER

Бренд: Champion Страницы: 31

Бренд: Champion Страницы: 36

Бренд: Champion Страницы: 37

Бренд: Champion Страницы: 38

Бренд: Brave Страницы: 12

Ribiland 042001

Бренд: Ribimex Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды