Wood-mizer LT15WB D17 Скачать руководство пользователя | Manualshive

Страница: 56 / 88

background image

Maintenance

Blade Wheel Belts

3

3-4

doc071918

Maintenance

4.

Make sure all safety warning decals are readable. Remove sawdust and dirt. Replace any dam-
aged or unreadable decals immediately. Order decals from your Customer Service Representa-
tive.

3.7

Blade Wheel Belts

WARNING!

Before performing service near moving parts such as blades, pul-

leys, motors, belts and chains, first turn the key switch to the OFF (#0) position
and remove the key. Failure to follow this may result in serious injury or death.

Rotate the blade wheel belts and check them for wear. Rotating the belts every 50 hours will pro-
vide longer belt life. Replace belts as necessary. Use only B57 belts supplied by Wood-Mizer.

3.8

Drive Belt Adjustment

WARNING!

Disconnect and lockout power before performing any service to

the electrical system. For battery-powered equipment, disconnect the negative
battery terminal cable.Failure to follow this may result in injury and/or electrical
system damage.

WARNING!

Before performing service near moving parts such as blades, pul-

leys, motors, belts and chains, first turn the key switch to the OFF (#0) position
and remove the key. Failure to follow this may result in serious injury or death.

WARNING!

Do not adjust the engine drive belts or belt support bracket with

the engine running. Failure to follow this may result in serious injury or death.

See Table 3-2.

See the table below for drive belt tension specifications for your model sawmill.

Measure the belt tension with a gauge.

NOTE:

Wood-Mizer offers a belt tension gauge (Part No.

016309) that will let you accurately measure the belt tension.

New Belt Installation/New Sawmill Operation

Subsequent Adjustment

Engine/

Motor

Deflection

Inches (mm)

Installation

Force

lbs. (kg)

Check

After

First

Acceptable

Force

lbs. (kg)

Then

Check

Every

Deflection

Inches (mm)

Force

lbs. (kg)

ALL

1/2” (13mm)

14 lbs.

(6.35kg)

20 hrs

14 lbs.

(6.35kg)

50 hrs

1/2” (13mm)

14 lbs.

(6.35kg)

TABLE 3-2

50

«
...
54
55
56
57
58
...
»

Содержание LT15WB D17

























































































Отзывы:

Нет отзывов

Похожие инструкции для LT15WB D17

Бренд: ZIPPER MASCHINEN Страницы: 109

Бренд: Draper Страницы: 20

Бренд: Raider Страницы: 90

Бренд: sunjoe Страницы: 12

Бренд: Wallenstein Страницы: 48

1600001-2000000

Бренд: Mountfield Страницы: 44

Бренд: BE Ag & Industrial Страницы: 28

Agri Ease BE-25TLE65GX

Бренд: BE Ag & Industrial Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды