WIKA CPC7000 Скачать руководство пользователя

Страница: 37 / 93

WIKA operating instructions pneumatic high pressure controller, model CPC7000

0019104001D 10/2018 EN

6.4.3.4

Rate Stability Parameters

Rate parameters for the control rate can be found in the Control Settings App and can be configured using the Rate Stable Window

and Rate Stable Delay buttons. The Rate Stable Window button allows the user to enter a value as a percentage of the active

range of transducer. This value represents the pressure window within which the control rate value would be considered stable by

the user. The Rate Stable Delay button lets the user add a desired delay until the control rate is considered stable while being in

the rate stable window.

Rate Stability

Parameters

Figure 6.4.3.4 Rate Stability Parameters

6.4.3.5

Vent Rate

The Vent Rate button in the Control Settings App lets the user to determine the rate at which pressure will vent in vent mode. By

default the rate of the vent is set similar to the control rate. Figure 6.4.3.5 displays the vent rate setting. The maximum allowable

rate of vent is 60 bar/second and the minimum vent rate is limited to 1 bar/second.

Figure 6.4.3.5 Vent Rate

6. Operation

Содержание CPC7000






























































































Результаты поиска

Содержание CPC7000

Отзывы:

Похожие инструкции для CPC7000

Бренды по названию

Популярные бренды

WIKA CPC7000, Руководство по эксплуатации

Результаты поиска

Содержание CPC7000

Отзывы:

Похожие инструкции для CPC7000

Бренды по названию

Популярные бренды