WIKA CPC7000 Скачать руководство пользователя

Страница: 60 / 93

WIKA operating instructions pneumatic high pressure controller, model CPC7000

0019104001D 10/2018EN

Burst_Slow

Value inside upper and lower limits

This is the rate used during the transition from low

setpt to high setpt in the anticipated “burst range”

Burst_Slow?

Returns the slow rate for burst test

Burst_Fast

Value inside upper and lower limits

This is the rate used during the transition from atmo-

sphere to the low setpt

Burst_Fast?

Returns the fast rate for burst test

Burst_Result?

Pressure at which burst was detected. Will return 0 if

no burst found.

Calculate_as_found_linearity

Calculate linearity slopes and intercepts from true/

actual pressures

Caldisable

YES,NO

Sets whether or not calibration of the active transducer

is disabled.

Caldisable?

Returns whether or not calibration of the active trans-

ducer is disabled.

Cerr

None

Clears the error queue

Cmdset

Mensor, SCPI

Activates remote command set for instrument emula-

tion modes.

Cmdset?

Returns active command set identifier

Control

Instrument placed in Control Mode

Control?

Returns YES if instrument is in control. NO if otherwise

Crate

Slow, Medium, Fast, Variable

Sets the control rate, Variable mode is a predeter-

mined user defined rate setpt.

Crate?

<sp>CCCCCC<cr><lf>

Returns the control rate – CCCC is variable in length

and corresponds to the parameters for the CRATE

command

Ctype?

Returns the type of regulator

Decpt?

Returns the number of decimal points (see Resolution)

Default

None

Sets the default values

DHCP

ON or OFF

Reserved for DHCP setup

DHCP?

Reserved for DHCP setup

DIO

2 or 0

2 turns on the first digital output pin, 0 turns it off

DIO?

Returns status of the first input and output pin. Bit0 =

input’s status, Bit1 = output’s status.

DOUTFUNC

Sets the function for output pin <n> to NONE, STA-

BLE, MEASURE, CONTROL, VENT

DOUTFUNC? <n>

Returns the function for output pin <n>

DINFUNC

Sets the function for input pin <n> to NONE, MEA-

SURE, CONTROL, VENT, KEYLOCK, START,

READING

DINFUNC? <n>

Returns the function for output pin <n>

DOUTSTATE

Turns output pin <n> to high, or low. Sets the function

for that pin to “None”

DIOSTATE?

Bit 0-5 is the status of the Input bits, Bit 6-11 are the

status of the Output bits. Returns an integer between

0 and 4095

DOC

mm/dd/yyyy

Sets the date of cal for the active transducer.

DOC?

Returns the date of cal for the active transducer.

DOM?

Returns the date of manufacture

Error?

<sp> text description <cr><lf>

Returns the next error in the error queue

7. Remote Operation

Содержание CPC7000






























































































Результаты поиска

Содержание CPC7000

Отзывы:

Похожие инструкции для CPC7000

Бренды по названию

Популярные бренды

WIKA CPC7000, Руководство по эксплуатации

Результаты поиска

Содержание CPC7000

Отзывы:

Похожие инструкции для CPC7000

Бренды по названию

Популярные бренды