WIKA CPC7000 Скачать руководство пользователя

Страница: 24 / 93

WIKA operating instructions pneumatic high pressure controller, model CPC7000

0019104001D 10/2018EN

6.4 Applications

6.4.1 Home Applications

The Home App is the normal operation screen. This application is different from the others in that it is not used to

setup the configuration but is used to monitor the pressure applied to the installed transducers

The screen in Figure 6.4.1-A shows the basic Home App in an instrument. The user can change the display to show multiple

auxiliary displays by pressing the auxiliary button on the left corner of the screen (Figure 6.4.1-B Home App With Auxilliary). The

Units button is always displayed. When the Units button is pressed a selection of imperial and metric units will be displayed on the

right (Figure 6.4.1-C Pressure Units); notice that the Units button has a lighter background when the selection menu is active. If a

barometric reference is installed, the Mode button, described below, will toggle from Gauge to Absolute mode when pressed.

Figure 6.4.1-A Basic Home App

Figure 6.4.1-B Home App with Auxiliary Display

Figure 6.4.1-C Pressure Units

6. Operation

Содержание CPC7000






























































































Результаты поиска

Содержание CPC7000

Отзывы:

Похожие инструкции для CPC7000

Бренды по названию

Популярные бренды

WIKA CPC7000, Руководство по эксплуатации

Результаты поиска

Содержание CPC7000

Отзывы:

Похожие инструкции для CPC7000

Бренды по названию

Популярные бренды