WIKA CPC7000 Скачать руководство пользователя

Страница: 17 / 93

WIKA operating instructions pneumatic high pressure controller, model CPC7000

0019104001D 10/2018 EN

4. Transport, Packaging and Storage

EU).

3.8 Warnings and Cautions

WARNING!

HIGH PRESSURE!

High pressure gases are potentially hazardous. Energy stored in these gases and liquids can

be released suddenly and with extreme force. High pressure systems should be assembled and operated only by

personnel who have been trained in proper safety practices.

WARNING!

NOT EXPLOSION PROOF!

Installation of this instrument in an area requiring devices rated as intrinsically safe is not

recommended.

WARNING!

POSSIBLE INJURY!

The tubing, valves, and other apparatus attached to the gauge must be adequate for the

maximum pressure which will be applied, otherwise physical injury to the operator or bystanders is possible.

CAUTION

USE THE PROPER PRESSURE MEDIUM!

Use only clean, dry, nitrogren of class 2.8 or better unless otherwise

specified by Mensor. This instrument is not designed for air use.

CAUTION

As with most sensitive electronic equipment, switch the power switch off before connecting or disconnecting to a

power source to prevent data loss. Do not position the equipment so that it is difficult to disconnect the AC power

cord.

WARNING!

Detachable main power supply cord delivered with inadequate ratings should not be used, it is recommended to use

the power cord delivered with the instrument. See Section 11 Specifications for power ratings.

Additional Warning and Caution notices are found throughout this manual.

Содержание CPC7000






























































































Результаты поиска

Содержание CPC7000

Отзывы:

Похожие инструкции для CPC7000

Бренды по названию

Популярные бренды

WIKA CPC7000, Руководство по эксплуатации

Результаты поиска

Содержание CPC7000

Отзывы:

Похожие инструкции для CPC7000

Бренды по названию

Популярные бренды