Volvo SDLG LG956L Скачать руководство пользователя страница 68

Страница: 68 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

1.2 Introduction of Gauges & Controls

The introduction of gauges & controls needed for operating the machine is below. Be sure to

understand their functions and methods for use.

1.2.1 Vehicle Gauges and Lights

Engine Water Temperature Gauge

This gauge indicates the temperature of engine water.

When the temperature index lies in the green ranges (60 ~100 ),

℃

the water temperature is normal.

Notice:

If the temperature index moves past green into the red range, be sure to

stop the machine for inspection.

Refer to

3.4.2 Steps to Stop Engine

in this chapter for details

of stopping the engine.

Torque Converter Oil Temperature Gauge

This gauge shows the torque converter oil temperature

When the temperature index lies in the green range (60 ~120 ),

℃

the oil temperature is normal. If the temperature index moves past green

into the red ranges, be sure to stop the machine for inspection.

Working Chronometer

This indicator shows the total operation hours of the machine; its

value can be used as a reference for inspection and maintenance.

Gearbox Oil Pressure Gauge

This gauge indicates the pressure of the gear-shifting system.

If the pressure index lies in the green range (1.1MPa~1.5MPa),

the oil pressure is normal. Be sure to stop the machine for

inspection if the index moves outside this range.

If the pressure index lies in the range of (11~15)×100kPa or

(15.95~21.75) ×10PSI, the oil pressure is normal. Be sure to

stop the machine for inspection if the index moves outside this

range.

Содержание SDLG LG956L



































































































































Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды

Volvo SDLG LG956L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды