Volvo SDLG LG956L Скачать руководство пользователя страница 86

Страница: 86 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

Put the gear control lever at forward I or backward I

position.

Press the brake pedal; press the parking brake level

to release the brake status.

Release brake pedal, and step on the accelerator
pedal slowly to drive the machine forward or
backward.

It is safe to drive only when the brake pressure is
over the specific value of 0.45MPa.

Never

lift the bucket to the highest position while

transporting material. The lower hinge of the arm working equipment should be 400mm

～

500mm above the ground to ensure stable driving in the transporting process.

△

NOTICE

Never

run at high speed if the machine goes on a slope or

uneven ground.

Select the proper transmission gears when go down a slope
and

never

change the gears during that time.

Never

run over speed while driving on a slope, and use the

foot brake pedal to slow the speed.

3.3.2 Gearshift. Changing between Forward and Backward

Press the accelerator properly when shifting gear to avoid sharp speed increase.

It is best to change the running direction (from forward to backward or from backward to forward)

after stopping the machine to get the best driver comfort and prolonging the life of the engine.

No need to stop and brake the machine to shift gears while running. Release the accelerator and

operate the transmission lever at the same time when changing the speed from low to high and

when changing the speed from high to low, release the accelerator first and then change the

transmission slowly.

Содержание SDLG LG956L



































































































































Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды

Volvo SDLG LG956L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды