Volvo SDLG LG956L Скачать руководство пользователя страница 79

Страница: 79 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

until the indicator lamp 1 turns off and the compressor stops working. Now the setting

temperature is the temperature in the cab. When the inside temperature is higher than the

setting temperature, the indicator lamp 1 lightens and the compressor will begin to refrigerate;

when the inside temperature is lower than the setting temperature, the indicator lamp 1 turns

off and the compressor stops working.

b) Heating

Before using, turn the temperature control switch to the ‘O’ position (the state of off).

Open the hot water valve and start engine.

Open the air volume and power switch 2 to choose the position of gear and adjust to the

desired air volume.

1.2.9.2

Ⅱ

control panel and is operation (if assembled)

The Appearance of Panel

Operating methods

Refrigeration

First-time use, turn the air volume and power switch to high gear after the engine started,

turn the temperature control switch to refrigeration. Turn the air volume to obtain low,

middle and high volume of air.

b) Heating

Turn the temperature control switch to the state of off, open the hot water valve the air

volume and power switch, warm air blow constantly. Turn the air volume and power switch

to obtain low middle and high volume of air.

c) Power

indicator

lamp

1. Air Volume and Power Switch 2.The Switch to Control The Temperature
3. Refrigeration Indicator Lamp 4. Power Indicator Lamp

Содержание SDLG LG956L



































































































































Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды

Volvo SDLG LG956L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды