Volvo SDLG LG956L Скачать руководство пользователя страница 30

Страница: 30 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

5 SAFETY DRIVING

5.1 Warning

The warning light should be turned on to warn the

other drivers on the road when the machine is

broken down or operating at a low speed.

5.2 Safety of self and others

Develop good driving habits to ensure everyone’s safety.

Sound the horn to ensure safety before moving.

Be sure there are no people or blockage on the left

and right side.

Check the brakes on dry and firm, level ground.

Do not put an arm or foot on the working

equipment or extend outside the machine.

When driving on the level ground, adjust the lower

hinge of the arm working equipment to 400

～

500mm(16

～

20in) above the ground.

Always warn people near the machine in all

direction by sounding the horn.

The door of the cab should be locked when driving. Do not open the door while driving.

It is dangerous to pick up other people. No one

should sit on the machine body.

Содержание SDLG LG956L



































































































































Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды

Volvo SDLG LG956L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды