Volvo SDLG LG956L Скачать руководство пользователя страница 73

Страница: 73 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

Rear Headlight Switch:

Press bottom side, the low beam of rear headlight on the engine hood will come on;

Press top side, the high beam of rear headlight on the engine hood will come on.

If no side is pressed, the lamps will go off.

Front Headlight Switch (if assembled):

Press bottom side, the low beam of the front headlight on the front frame will come on;

Press top side, the high beam of the front headlight on the front frame will come on;

If no side is pressed, the lamp will go off.

Front (Rear) Lighting Lamp Switch:

Press bottom side, the front headlight and rear lighting lamp on the top of cab will come on;

Press top side, no lamp will come on.

Back Light Switch (if assembled):

Press bottom side, the back light, head light and tail light will come on together;

Press top side, no lamp will come on.

Warning Lamp Switch (if assembled):

Press bottom side, all the turning lamps will blink for an emergency circumstance, sending light

to warn the other vehicles and passersby. Press top side, all the turning lamps will stop blinking.

Warning Button Switch (if assembled):

When this button is pushed down, all the turning lamps will blink for an emergency circumstance,

sending light to warn the other vehicles and passersby. When the button springs back, all the

turning lamps will stop blinking.

Rain wiper Switch:

Press bottom side, rain wiper will work; press top side, the rain wiper will stop.

Water Spraying Switch:

Press bottom side, spray water to the front glass of the cab; press top side, stop spraying.

Top Lamp Switch:

This switch is behind the ceiling lamp in the operator cab.

Содержание SDLG LG956L



































































































































Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды

Volvo SDLG LG956L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды