Volvo SDLG LG956L Скачать руководство пользователя страница 95

Страница: 95 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

3.6 Oil and Fuel Supply

3.6.1 Engine Oil Supply of Engine

①

Oil Level Checking

△

NOTICE

An oil level check must be executed 15 minutes before engaging the

engine, or after stopping the engine.

Park the machine on level ground, and put the transmission lever in the

neutral

(“

”) position.

Pull the brake valve manual control handle or press the parking brake switch to brake, and put

blocks in front and back of tires.

Open the side door on the right side of the engine cover.

Pull the dipstick out, and wipe it clean with a cloth. Insert the dipstick back, and pull it out again

to check the oil level (at least twice).

Weichai WD10G220E13 engine:

The oil level is normal if the oil level is between ‘H’ and

‘L’ limit; If the level is lower than the ‘L’ limit, oil should be added by the oil adding port.

Shangchai C6121ZG50B engine:

The oil level is normal if the oil level is between ‘Still

full’ and ‘Adding oil’ limit at the still side of the dipstick; If the level is lower than the

‘Adding oil’ limit, oil should be added by the oil adding port.

Содержание SDLG LG956L



































































































































Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды

Volvo SDLG LG956L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды