Volvo SDLG LG956L Скачать руководство пользователя страница 28

Страница: 28 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

condition. Operate only after the abnormal conditions are resolved.

To avoid fire, check whether there are any flammable materials such as wood chips, leaves and

paper which have accumulated on the engine.

Check whether there is leakage of oil, or water, loose nuts, abnormal sounds, broken or lost parts.

Check the cab floor, rearview mirror, control lever (or control handle), pedal and handrails for oil,

grease, snow or dirt, and clean.

Check the level of coolant, fuel and make sure the level of engine oil in the pan is normal. Please

refer to

CHAPTER III – 3.6 Supply of Oils,

to check whether the air filter is blocked.

Adjust the operator’s seat to the proper position for operation. Please refer to

CHAPTER III

– 1.2.10 Seat Adjustment

to check whether the safety belt and the fixed equipment (if

assembled) are broken.

The safety belt must be replaced with a new one every three

years.

Check the gauges for damage, and make sure the control lever (or control handle) is in the

braking position.

Clean the dirt on the cab window and all the lamps to ensure better visibility.

Adjust the rear-view mirror and keep the surface clean to ensure the best view from the operator’s

seat. Replace with a new one if the mirror has been damaged.

Don’t leave any tool or part around the operator’s seat. They may fall because of the vibration

during moving and working, which could break the control lever (or control handle) or switch, or

move the control lever (or control handle) which could start the working equipment and cause an

accident.

Check whether the floodlight and signal light is normal and repair if not.

Check whether the front and rear frames is unlocked.

Clean oil from the handrail and the pedal and the silt and sand from the shoes to avoid slippage,

which may affect the operations.

Check whether the tires are worn or broken, the bolts and nuts are loose. Especially pay attention

to the loose hub nut and repair or replace for any

abnormal situations.

4.1.3 When Starting the Engine

Before boarding on the machine, check the machine

again to see whether there are people or blockages

on or under or near the machine. If there are

unrelated people in the working area, ask them to

leave. Do not begin work until they leave.

Содержание SDLG LG956L



































































































































Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды

Volvo SDLG LG956L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды