Volvo SDLG LG956L Скачать руководство пользователя страница 40

Страница: 40 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

insulator).

At least 6m (20ft) at 40KV high voltage condition (electric wire is generally supported by
hanging insulator).

The vertical distance between loader and the overhead electric wire should be:

At least 2m (6.5ft) at low voltage condition.

At least 4m (13ft) at high voltage condition.

To prevent an accident, please do as follows:

First ask the electricity company for the voltage. Check the validity of action according to the
relevent rules when the machine may touch the electric cables.

Wear rubber shoes and rubber gloves. Lay a leather cushion over the operator’s shoes. Be sure no
part of your body can touch the metal bottom.

Assign a signal warner, who can give a warning when the machine gets too close to electric
cables.

Never

leave the operator cab,

never

move and do not touch any part of the machine until the

people who are on the ground cut off the electricity once the machine touches the wire.

When operating near high-voltage cables, make sure other persons are far from the machine.

7 SAFETY PARKING

7.1 Pay Attention to the Safety of Yourself and Others

Park the machine on level ground. The working equipment should be put on the ground.

Never

park on a ramp. If parking on a ramp is necessary, the ramp angle should be less than 20%,

and put the wedge under the wheels to prevent moving. Then put the bucket down to the ground.

If the machine is disabled or must park in a high traffic area, lay bars, signals, flags and warning

lights. Make sure the other cars can see it clearly. Do not block traffic.

When parking the machine, unload all the material on the machine, lower the bucket to the

ground, stop the engine, pull the parking brake switch and put it in the braking position. Lock the

engine and put away the keys. Climb down with face to the machine slowly, according to the

“3-points” method.

Never

jump down to the ground.

△

WARNING

NEVER

get on or off the machine while it is moving.

Содержание SDLG LG956L



































































































































Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды

Volvo SDLG LG956L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды