Volvo SDLG LG956L Скачать руководство пользователя страница 103

Страница: 103 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

Disassemble the negative electrode of the battery and cover it, or remove it from the machine and

store it separately.

Lower the bucket to the ground and set all control handles to the

Neutral

position. Pull the brake

valve control handle or press the parking brake switch and lock the cab door.

3.7.2 During Storage

△

WARNING

Open doors and windows to ensure ventilation and exhaust to allow

of poisonous gas if the antirust is used in the building.

Start the machine once a month so that lubricant can be coated over the surface of the movable parts

and other components surfaces. The battery in storage can be charged at the same time.

Wipe off the grease which has coated the hydraulic cylinder rods before work and operation.

3.7.3 After Storage

Do as follows after long-term storage of machine.

Wipe off the grease coated on the hydraulic cylinder rods.

Add oil and grease to all the requisite positions.

Содержание SDLG LG956L



































































































































Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды

Volvo SDLG LG956L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды