Volvo SDLG LG956L Скачать руководство пользователя страница 33

Страница: 33 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

5.6 Pay Attention to Blockages

If there are blockages (roof of buildings or the door frame), keep the loader away from the
blockages when turning or passing.

Notice the environment. Slow down and check whether there are some blockages when turning or
going through a narrow passageway.

Operate carefully to prevent unstable loads when the ground is uneven and the load is not stable.

5.7 Driving in Dangerous Conditions

Do not operate when you are unsure about the

environment. Investigate the condition of the road,

the strength of the bridge, landform of the working

area and all geologic features before working.

Pay attention to the depth that the tires sink and the

braking effect on muddy or soft ground.

When working in water or swampland, prevent the

bottom of the axle housing from being soaked. Slow

down after passing through water or during rain.

Step on the brake pedal gently and alternately to let

the skid device dry after working in water or in rain.

The clay piled on the ground or near the canal is

usually soft.

Never

allow a turn over caused by the

weight or vibration of the loader.

Never

drive the machine near hanging things or close to a deep ravine. The machine weight or

vibration may cause the ground to collapse, and result in the machine turning over.

Assemble anti-fall and anti-turn operator cab when working in an area where there is danger of

falling stone and machine turnover.

Continual rainy weather, earthquake and explosions can cause dangerous working conditions.

Operate carefully in these cases.

Drive at a low speed, prevent starting, braking or turning suddenly, and use the tire chain on a

snowy road. Brake alternately. Lower the bucket to touch the ground to brake if necessary.

The load should be decreased to prevent slippage when driving on snowy ground because the

adhesive force may change greatly in the piled snow.

Содержание SDLG LG956L



































































































































Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды

Volvo SDLG LG956L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды