Volvo SDLG LG956L Скачать руководство пользователя страница 43

Страница: 43 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

middle and wedge the tire from the opposite side. Put the cushion blocks under the machine.

8.4 Working under the Machine

Park the machine on firm ground. Lower the working equipment to the ground before working

under the machine.

Wedge the tire firmly.

It is dangerous to work under the machine only using

the working equipment to support the machine.

Never

work under the machine without good

support.

8.5 Working on the Machine

Make sure the top of the machine has no blockage and is clean when working on the top of the

machine. Follow the rules below:

△

NOTICE

Do not allow lubricant or grease to leak.

Do not randomly put the tools around the work place.

Walk slowly and carefully.

Never

jump down from the machine. When climbing up and down the machine, face the machine

and keep three points contact (two hands-one foot or two feet-one hand) with the handrails and

pedals to ensure safety.

Use protective equipment if necessary.

Never

stand on the top of the engine hood because it is slippery and dangerous.

Never

stand on the top of tires because they are slippery and dangerous.

Stand on the mudguard of the front frame and seize the handrail to clean the front glass of the

operator cab.

Содержание SDLG LG956L



































































































































Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды

Volvo SDLG LG956L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды