Volvo SDLG LG956L Скачать руководство пользователя страница 99

Страница: 99 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

△

WARNING

If the temperature of the gearbox oil is relatively high, please wear

protective clothes, and operate carefully to prevent injury.

Drain all the oil out and clean the oil on the draining plug

and the transmission box, and wear new raw meal on the

oil draining plug and assemble it well.

Loosen the cover of oil adding port on the right side of the

frame joint position. Inject the prescriptive hydraulic

transmission oil (about 45L), and then fasten the cover of

the oil adding port.

Start the engine and run in the idle status for several minutes. Check the oil level of the

transmission box.

△

NOTICE

If the old oil is dirty, do not add new oil directly. Disassemble the

raw oil filter which is in profile, and clean all the parts. If there

are any metal powders or fragments please contact the

maintenance man.

Assemble the parts, and add a little new hydraulic transmission

oil. Start engine and hold in the idle status for 3~5 minutes.

Release the oil in the oil pan and add new oil.

3.6.4 Adding Oil to Axle

①

Oil Level Check

Park the machine on level ground and put the transmission lever in the

neutral

position. Pull the

brake valve manual control handle or press the parking brake switch to carry out braking, and

wedge the front and back of the tire. Loosen the oil adding plug in the middle of the front and

rear axles. It is proper if the oil level is at the bottom side of the oil adding port, otherwise please

add axle oil. Please watch for about 5 minutes after adding oil. If the oil level keeps stable, please

assemble the oil adding plug. For selections of gear oil, please refer to

CHAPTER IV 2.2

Selection of Oil, Fuel and Coolant

Содержание SDLG LG956L



































































































































Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды

Volvo SDLG LG956L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды