Volvo SDLG LG956L Скачать руководство пользователя страница 70

Страница: 70 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

Pre-heat Indicator Lamp:

The lamp will come on if start switch is turned to preheat position

when machine is equipped with cold start equipment; the lamp will be off if start switch is turned to

other position.

Oil Pressure Warning Lamp:

The lamp will come on immediately if the start switch is turned

on. It will go off immediately after the engine is started. Otherwise it means the level of lubricant is

too low or there is some problem with the lubricant system. Then shut the engine and check it.

Charging Indicator Lamp:

The lamp will come on if the start switch is turned on. It will go off

immediately after the engine is started. Otherwise it means there is some problem with storage battery.

Please examine and repair it.

Power Cut Indicator Lamp:

The lamp will come on if the power is cut off, and it will go off if

the power is not cut off.

When braking pedals are installed on the two sides, the power will be cut off and the lamp will

come on if the left braking pedal is stepped down; the power will not be cut off and the lamp will go

off if the right braking pedal is stepped down.

Emergency Steering Indicator Lamp:

The emergency steering function is selected to install.

When the wheel loader is steered emergently, the lamp will come on if the emergency steering pump

works.

Parking Brake Indicator Lamp:

If the brake air pressure is normal, the lamp will come on

when the brake valve manual control handle is pulled up (or the parking brake switch is pushed

down). The lamp will go off when the brake valve manual control handle is pushed down (or turn the

parking brake switch to spring back); the lamp will also come on if the brake air pressure is low.

Low Brake Air Pressure Alarm Lamp:

The lamp will come on for a warning if the brake air

pressure is below 0.4MPa.

High Beam Indicator Lamp:

The lamp will come on if the high beam is used in the front head

light. The lamp will go off if the low beam is used in the front head light or the front head light is off.

Computer box working Indicator Lamp:

The ZF or 4WG180 gearbox is selected to install, the

indicator lamp will come on if the starting switch is on, otherwise, please stop to exclude the error.

Fuel Prefiltration Indicator Lamp:

The lamp will come on when the fuel preliminary filter is

blocked. Please clean it or replace.

Turning Indicator Lamp:

The lamp will come on if the steering switch is connected,

meanwhile, the steering lamp will come on. The left indicator lamp will come on if turn to left, and

the right indicator lamp will come on if turn to right.

Содержание SDLG LG956L



































































































































Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды

Volvo SDLG LG956L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды