Volvo SDLG LG956L Скачать руководство пользователя страница 37

Страница: 37 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

Be careful when the lift arm reaches the upper limit. Loading in the upper limit position may
cause destabilization of loader. So the driving speed
should be slow and the bucket should tilt forward
slowly.

When unloading to the truck or tipper, make sure the

bucket does not hit the truck or tipper. Do not allow

anyone to stand under the bucket or to let the bucket

go over the cab of the truck.

When driving backwards, ensure visibility of what is

behind you.

Install lighting systems during dark conditions. And

stop work when there is smoke, fog, sand, or dust

which affects visibility.

When working at night, please make sure:

Proper lighting system is installed.

Fuction light works normally.

To carefully estimate the height and distance of

objectives.

Keep alert and stop the engine and examine the

environment and the machine frequently.

Make sure that every bridge is strong enough to let

the machine pass.

Содержание SDLG LG956L



































































































































Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды

Volvo SDLG LG956L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды