Volvo SDLG LG956L Скачать руководство пользователя страница 35

Страница: 35 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

5.9 Towing

△

WARNING

Injury, even death may occur if the disabled machine is towed incorrectly.

Follow the direction in

CHAPTER III – 3.5.2 (7) Towing Operation

, a dangerous

contion may be caused by using the wrong method.

Wear gloves to deal with a tightwire.

Before preparation for the towing confirm the signals with other people.

Please contact Shandong Lingong Construction Machinery Co. Ltd. or their accredited

representative if the engine does not start or the brake system has problems.

Please tow the machine on level ground; it is dangerous to tow on a ramp.

If a disabled machine is towed by an other machine,

the tightwire should be strong enough to pull the

weight of the towed machine. The tightwire with

wring or radius reduction can not be used.

People are not allowed to go between two

machines when the machines are connected.

Do not stand on the towing steel wires or

tightwires.

Keep the hook of the towing machine and the towing parts in a horizontal line.

Содержание SDLG LG956L



































































































































Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды

Volvo SDLG LG956L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды