Volvo SDLG LG956L Скачать руководство пользователя страница 112

Страница: 112 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

107

necessary to change the kind of fuel according to the ambient temperature.

Always

fill the fuel tank full after operating to prevent the water, which is condensed by the

moisture in the air, from entering the fuel tank.

If the engine fails to suck fuel or the filters have been just replaced, drain out the air in the circuit.

2.1.2 Coolant

Always

use glycol type engine antifreeze as coolant..

If the engine overheats, add coolant until the engine cools down completely.

Add coolant to specified level. If the level is too low, it will cause the overheating of the engine

system and the corrosion of the cooling system.

Antifreeze is flammable. Keep fire away when adding the antifreeze.

When adding antifreeze, select different types of antifreeze according to the condition of

circumstance, the recommended range to select is:

If the ambient temperature

≥

-15

℃

use -25#

If the ambient temperature

≥

-25

℃

use -35#

If the ambient temperature

≥

-35

℃

use -45#

2.1.3 Lubricant

Lubricant is used to reduce noise and prevent wear on the joint surfaces.

Joints not included in the manual (connectors, jointing sleeves) are treated during overhaul. So

they do not need be lubricated. When some parts become inflexible because of long-term

operation, it is necessary to add lubricant.

Remember to wipe off the overflow lubricant when adding it.

2.1.4 The Storage of Oil and Fuel

Prevent water, dirt or other impurities from mixing with the oil.

Follow the rule, first in first out, to maintain oil quality during long-term storage (Use the oil with

the longest shell life).

2.1.5 Filters

Filters are extremely important safety components. They can prevent impurities in the fuel from

entering important equipment and causing problems. Replace all filters periodically. For the

maintenance cycle, refer to

3 CONTENT OF MAINTENANCE

, in this chapter. Replace filters

at shorter intervals when the machine works in a severely bad environment.

Never

try to clean paper filter elements and use them again.

Always

replace them with a new

one.

When replacing the oil filters, check whether there are some metallic particles adhering to the old

Содержание SDLG LG956L



































































































































Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды

Volvo SDLG LG956L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG956L

Отзывы:

Похожие инструкции для SDLG LG956L

Бренды по названию

Популярные бренды