Trane BMUC600AAA0100011 Скачать руководство пользователя страница 5

Страница: 5 / 84

BAS-SVX45F-GB

BACnet MS/TP Link Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
BACnet/IP Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Wiring Inputs and Outputs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Providing Low-voltage Power for Inputs/Outputs

. . . . . . . . . . . . . . . . . . . . . . 29

Input and Output Wiring

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Wiring Universal Inputs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Wiring Binary Inputs  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30
Wiring 0–10 VDC Analog Inputs  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31
Wiring 0–20 mA Analog Inputs   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  32
Wiring Variable Resistance Analog Inputs   . . . . . . . . . . . . . . . . . . . . . . . .  33

Wiring Trane Zone Sensors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Wiring Analog Outputs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Wiring Binary Outputs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Connecting Pressure Transducer Inputs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Tracer UC600 Operation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

LED Descriptions and Activities

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Troubleshooting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Communication Problems   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  39
Output Points  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  39
Connection Problems  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  40

Configuring Tracer UC600 with Tracer TU

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Starting a Session of TU and Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Connecting Using Tracer SC

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Tracer TU Installation and Connection Error Conditions . . . . . . . . . . . . . 44

Upgrading Firmware

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Configuring Tracer UC600 and Creating or Editing Points

. . . . . . . . . . . . . . 46

Monitoring and Viewing the Status of the Tracer UC600

. . . . . . . . . . . . . . . 53

Backup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Transfer Files (Restore)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Setting Up and Maintaining Schedules

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Creating a Weekly Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  55
Changing the Schedule Default Value and Adding Events  . . . . . . . . . . .  57
Adding Exceptions to a Schedule   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  59
Modifying Exceptions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  62

Содержание BMUC600AAA0100011





















































































Результаты поиска

Содержание BMUC600AAA0100011

Отзывы:

Похожие инструкции для BMUC600AAA0100011

Бренды по названию

Популярные бренды

Trane BMUC600AAA0100011, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BMUC600AAA0100011

Отзывы:

Похожие инструкции для BMUC600AAA0100011

Бренды по названию

Популярные бренды