Trane BMUC600AAA0100011 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 84

Trane BMUC600AAA0100011 Скачать руководство пользователя страница 3

BAS-SVX45F-GB

3

Introduction

Copyright

This document and the information in it are the property of Trane, and may not be used or
reproduced in whole or in part without written permission. Trane reserves the right to revise this
publication at any time, and to make changes to its content without obligation to notify any person
of such revision or change.

Trademarks

All trademarks referenced in this document are the trademarks of their respective owners.

Revision History

BAS-SVX45E-EN:

•

Revisions made to “Setting the BACnet Device ID” section.

•

Appendix added: Configuring Tracer UC600 for BACnet/IP.

•

Terminology change: WCI now called Air-Fi™ Wireless.

•

Revisions made to “Configuring the Tracer UC600 with the Tracer TU Service Tool” section.

•

PICS appendix removed; Reference the literature in the Other Resources section.

BAS-SVX45D-EN:

•

UL864 certified (smoke control systems).

•

Wireless support (WCI).

BAS-SVX45C-EN:

•

Creating and viewing Schedules.

•

Viewing custom graphics.

«
1
2
3
4
5
...
»

Содержание BMUC600AAA0100011





















































































Отзывы:

Нет отзывов