Trane BMUC600AAA0100011 Скачать руководство пользователя страница 6

Страница: 6 / 84

BAS-SVX45F-GB

Deleting Events  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  62
Deleting Exceptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  63
Deleting a Schedule   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  63

Custom Graphics

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Graphics Best Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Commissioning/Troubleshooting in a Powered State

. . . . . . . . . . . . . . . . . . . . . 66

Resistive Inputs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Voltage Inputs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Current Inputs - Methods 1 or 2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

24 Vac Measurement

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Binary Inputs, 24 Vac Detect- Methods 1 or 2

. . . . . . . . . . . . . . . . . . . . . . . . . 71

Binary Inputs- Based on Analog Output Connection

. . . . . . . . . . . . . . . . . . . 71

Open-collector Based Binary Sensors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Voltage Analog Output

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Current Analog Output- Methods 1 or 2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Ground Measurements

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Other Resources

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Appendix A: Configuring Tracer UC600 for BACnet/IP

. . . . . . . . . . . . . . . . . . . . . 76

Device ID Assignment for Trane BACnet/IP Devices

. . . . . . . . . . . . . . . . . . . . 76

Ethernet Network Wiring Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

BACnet/IP Network Configuration on the Tracer SC

. . . . . . . . . . . . . . . . . . . . 76

Enabling BBMD Functionality on the IP Network . . . . . . . . . . . . . . . . . . . 77

Setting Up Tracer UC600 BACnet Communication With Tracer TU

. . . . . . . 78

Establishing a Direct Connection with Tracer TU  . . . . . . . . . . . . . . . . . . .  78
Establishing a Network Connection with Tracer TU . . . . . . . . . . . . . . . . .  79
Configuring IP Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  79
Configuring BACnet Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  80
Setting Up a BDT  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  81

Security

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Local Network (Firewall) Security   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  81
Disable HTTP Communications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  82
Disable Tracer UC600 User Interface (TD7) . . . . . . . . . . . . . . . . . . . . . . . .  82

Declaration of CE Conformity

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Содержание BMUC600AAA0100011





















































































Результаты поиска

Содержание BMUC600AAA0100011

Отзывы:

Похожие инструкции для BMUC600AAA0100011

Бренды по названию

Популярные бренды

Trane BMUC600AAA0100011, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BMUC600AAA0100011

Отзывы:

Похожие инструкции для BMUC600AAA0100011

Бренды по названию

Популярные бренды