Trane BMUC600AAA0100011 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 84

background image

82

BAS-SVX45F-GB

Appendix A: Configuring Tracer UC600 for BACnet/IP

Disable HTTP Communications

HTTP is used for Tracer TU network connections and future UC600 BACnet/IP display options.
Tracer TU can also connect directly through the USB port, with a Tracer SC, or another Tracer UC600
on the IP network.

For added security, HTTP Port 80 should be disabled if other connection options are viable (see

Figure 45, p. 80

). This will prevent others from accessing the Tracer UC600 with a Web browser or

other HTTP applications. HTTP Port 80 is disabled with the Tracer TU service tool as described in

“Configuring IP Information,” p. 79

Disable Tracer UC600 User Interface (TD7)

If direct Tracer TU network addressing is needed, then access to the user interface through a Web
browser should be disabled. (See

Figure 45, p. 80

). This is done with the Tracer TU service tool as

“Configuring IP Information,” p. 79

.

Note:

At this time the Tracer TD7 display option is not available when connecting with the BACnet/
IP protocol. This option will be available in a future Tracer UC600 firmware upgrade.

«
...
80
81
82
83
84
»

Содержание BMUC600AAA0100011





















































































Отзывы:

Нет отзывов

Похожие инструкции для BMUC600AAA0100011

Бренд: TCS Basys Controls Страницы: 2

Бренд: Bang & Olufsen Страницы: 80

Бренд: Bang & Olufsen Страницы: 13

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

Бренд: Eaton Страницы: 100

Бренд: janitza Страницы: 58

Бренд: Laird Страницы: 38

Бренд: Laird Страницы: 5

Бренд: National Instruments Страницы: 2

Бренд: Omega Страницы: 56

Бренд: Omega Страницы: 2

Digiplex DGP-848

Бренд: Paradox Страницы: 20

Бренд: xpr Страницы: 4

Бренд: Zeta Страницы: 44

Бренд: Dahua Страницы: 137

Бренд: Ultraflex Страницы: 7

Бренд: D&R ELECTRONICS Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды