Trane BMUC600AAA0100011 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 84

background image

78

BAS-SVX45F-GB

Appendix A: Configuring Tracer UC600 for BACnet/IP

Setting Up Tracer UC600 BACnet Communication With Tracer TU

The procedures in this section describe how to initially connect to Tracer TU through a USB cable,
and then make the necessary BACnet/IP configurations in the Protocol group box on the controller
settings screen. Upon completion, you can connect to Tracer TU and view Tracer UC600 using the
BACnet/IP protocol. For more configuration tasks, see

“Configuring Tracer UC600,” p. 46

.

Note:

Tracer TU V8.6 or higher must be installed on Tracer UC600 to enable BACnet/IP
communication. Tracer UC600 firmware must be at V5.0 or higher.

Perform the following tasks in the order in which they are shown.

•

Establish a direct connection to Tracer TU.

•

Configure IP information

•

Configure BACnet information

•

Return to the Tracer TU Startup Task Panel to connect using the BACnet/IP protocol (see

“Establishing a Network Connection with Tracer TU,” p. 79

Establishing a Direct Connection with Tracer TU

To establish a direction connection:

1.

Connect a USB cable between the technician PC and the USB service port of the Tracer UC600.
The Startup Task Panel dialog box appears.

2. Select the Direct Connection radio button (

3. Click Connect.

Figure 43. Establishing a direct connection

«
...
76
77
78
79
80
...
»

Содержание BMUC600AAA0100011





















































































Отзывы:

Нет отзывов

Похожие инструкции для BMUC600AAA0100011

Бренд: UE Страницы: 4

Бренд: XBOX Страницы: 7

Бренд: Danfoss Страницы: 20

Бренд: Danfoss Страницы: 36

Бренд: tams elektronik Страницы: 60

Бренд: Garmin Страницы: 220

Бренд: Gardena Страницы: 16

Бренд: Samson Страницы: 40

Бренд: Kamstrup Страницы: 36

Бренд: JFA Electronicos Страницы: 29

Бренд: Velleman Страницы: 26

Бренд: Velleman Страницы: 32

Бренд: Velocity Страницы: 84

ArtNet-DMX Mux16

Бренд: DMX4ALL Страницы: 21

XP-9 88-IoT Series

Бренд: ICP DAS USA Страницы: 8

Бренд: ICON Страницы: 2

Бренд: ICP DAS USA Страницы: 4

Бренд: K&K Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды