Trane BMUC600AAA0100011 Скачать руководство пользователя страница 4

Страница: 4 / 84

BAS-SVX45F-GB

Table of Contents

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Smoke Control Support (UUKL)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Air-Fi™ Wireless Communications Interface (WCI) Support

. . . . . . . . . . . . . . 7

Expansion Module Requirements

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Location of LEDs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Hardware Terminations

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Agency Listings and Compliance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Additional Ordering Options

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Required Tools

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Dimensions and Clearances

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Mounting and Removing the Tracer UC600 Controller

. . . . . . . . . . . . . . . . . 13

DIN Unit Width

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Setting Addresses using Rotary Switches

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Setting the BACnet Device ID  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  16
BACnet MS/TP Device ID Assignment  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  16
Device ID Assignment for BACnet/IP Devices  . . . . . . . . . . . . . . . . . . . . . .  17
Device ID Assignment for Wireless Devices  . . . . . . . . . . . . . . . . . . . . . . .  17
Rotary Dial Address Settings for Non-Trane Systems  . . . . . . . . . . . . . . .  17

Tracer UC600 Pre-power Checks

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Resistive Inputs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Voltage Inputs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Current Inputs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Binary Inputs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Power Budget Check in an Un-powered State

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Calculating AC Power Consumption

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Calculating DC Power Consumption

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Wiring and Powering the Tracer UC600

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

AC Power Warnings and Cautions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Requirements and Recommendations

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Wiring and Circuit Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Transformer Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Avoid Equipment Damage!

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Terminal Connectors and Tug Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Wiring AC Power to Tracer UC600

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Controller Startup and Power Check

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Содержание BMUC600AAA0100011





















































































Результаты поиска

Содержание BMUC600AAA0100011

Отзывы:

Похожие инструкции для BMUC600AAA0100011

Бренды по названию

Популярные бренды

Trane BMUC600AAA0100011, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BMUC600AAA0100011

Отзывы:

Похожие инструкции для BMUC600AAA0100011

Бренды по названию

Популярные бренды