Trane BMUC600AAA0100011 Скачать руководство пользователя страница 26

Страница: 26 / 84

BAS-SVX45F-GB

Wiring and Powering the Tracer UC600

Controller Startup and Power Check

Verify that the 24 VAC connector and the chassis ground are properly wired.

2. Remove the 24 VAC connector from the Tracer UC600.

3. Remove the lockout/tagout from the line voltage power to the electrical cabinet.

4. Using a digital multimeter (DMM), verify that 24 VAC is present at the 24 VAC connector.

If voltage reading is within plus or minus 10%, connect the 24 VAC connector to the transformer
XMRF input on the UC600.

The following table describes the Tracer UC600 service and power LED indicators.

Table 8.

LED startup sequence

Power LED

Indicates...

Solid Green

Normal operation.

Blinking Red

Alarm or fault is present.

Solid Red

Low voltage or malfunction.

Sequence on Powerup:

Illuminates red, then green.

Service LED

Indicates...

Solid Green

LED has been pressed and remains on until powered down.

Blinking Green

Controller not accessing application software.

Not illuminated

Normal operation.

Sequence on Power-up:

Does not illuminate during power-up.

Содержание BMUC600AAA0100011





















































































Результаты поиска

Содержание BMUC600AAA0100011

Отзывы:

Похожие инструкции для BMUC600AAA0100011

Бренды по названию

Популярные бренды

Trane BMUC600AAA0100011, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BMUC600AAA0100011

Отзывы:

Похожие инструкции для BMUC600AAA0100011

Бренды по названию

Популярные бренды