Trane BMUC600AAA0100011 Скачать руководство пользователя страница 46

Страница: 46 / 84

BAS-SVX45F-GB

Configuring Tracer UC600 with Tracer TU

Configuring Tracer UC600 and Creating or Editing Points

Configuring Tracer UC600

Use the Tracer TU Controller Settings Utility to configure the Tracer UC600. This utility configures
date and time, units of measure, and protocol.

Navigate to Utilities > Status > Controller Settings. The Controller Settings utility opens.

Note:

The content of this screen is based on the type of controller that is connected and the
system protocol used to communicate with the controller.

2. Click Date and Time

to set the preferred date and time formats and then click Send to Device.

Optional: If daylight saving time is observed in the region where the Tracer UC600 resides,
select the Use Daylight check box. Select dates and time from the drop-down lists that follow
(see

Figure 23

3. Click Controller Units and set the preferred units of measure and then click Send to Device.

4. Click Protocol to display a list of protocols that the Tracer UC600 uses to communicate with

other controllers. For BACnet protocol, specify the

Baud Rate, and then click Send to Device.

5. If the device ID must be set manually (typically for 3rd party integrations), click Protocol again

and select the Use Soft Set Device ID check box. Enter a device ID, click Save, and then cycle
the power.

To return to the rotary dial Device ID setting, click Remove Soft Set ID

click Save, and then cycle

the power to the controller for changes to take effect.

Figure 23. Configuring the date and time

Содержание BMUC600AAA0100011





















































































Результаты поиска

Содержание BMUC600AAA0100011

Отзывы:

Похожие инструкции для BMUC600AAA0100011

Бренды по названию

Популярные бренды

Trane BMUC600AAA0100011, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BMUC600AAA0100011

Отзывы:

Похожие инструкции для BMUC600AAA0100011

Бренды по названию

Популярные бренды