Trane BMUC600AAA0100011 Скачать руководство пользователя страница 80

Страница: 80 / 84

BAS-SVX45F-GB

Appendix A: Configuring Tracer UC600 for BACnet/IP

Figure 45. Configuring IP information

Configuring BACnet Information

Navigate to the BACnet Settings frame.

2. In the Device ID section, use the current device ID or select the Use Software Device ID check

box and enter the device ID. (For more information about device IDs, see

“Device ID Assignment

for Trane BACnet/IP Devices,” p. 76

3. In the Protocol section, select the Enable BACnet/IP Communications radio button, and then

assign a UDP Port number. All devices on a BACnet/IP network must have the same UDP port
number.

4. Determine whether the Tracer UC600 must be a BBMD. If the device is BBMD, set up a BDT (See

“Setting Up a BDT,” p. 81

5. After all edits are complete, click Send to Device.

6. To return to the Startup Task Panel, disconnect from Tracer TU and then reconnect.

Figure 46. Configuring BACnet information

Содержание BMUC600AAA0100011





















































































Результаты поиска

Содержание BMUC600AAA0100011

Отзывы:

Похожие инструкции для BMUC600AAA0100011

Бренды по названию

Популярные бренды

Trane BMUC600AAA0100011, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BMUC600AAA0100011

Отзывы:

Похожие инструкции для BMUC600AAA0100011

Бренды по названию

Популярные бренды