Trane BMUC600AAA0100011 Скачать руководство пользователя страница 32

Страница: 32 / 84

BAS-SVX45F-GB

Wiring Inputs and Outputs

Wiring 0–20 mA Analog Inputs

Connect any 0–20 mA analog input to sensors such as humidity sensors and pressure sensors.

Connect the shield to a common terminal at the terminal board and tape it back at the input
device.

Note:

Do Not use the shield as the common connection. For 3-wire applications, use a 3-
conductor cable with shield and for 2-wire applications, use a 2-conductor cable with
separate shield.

2. Connect the signal wire to an available input terminal.

3. Connect the supply wire to a 24 VDC or 24 VAC terminal as required.

4. Use the Tracer TU service tool to configure the analog input that references the corresponding

hardware termination.

Figure 12. Typical wiring, 0–20 mA

IMC

OUT

+24

VDC

+24

VDC

OUT

VAC

MBUS

OUT

VAC

XFMR

VAC

OUT

IMC

+24

VDC

LINK

OUT

+24

VDC

+24

VDC

AO1

ADDRESS

0 1

x10

0 1

x100

0-20 mA out

Common

24 VDC

Tape shield back

2-wire

3-wire

Tape shield back

2-wire

0-20 mA out

24 VDC

Common

24 VDC

0-20 mA out

Top tier wiring: connect to any
UI input

Bottom tier wiring: connect to any
AO/UI input. Connect 24 VDC wire
to available 24 VDC on top tier.

Содержание BMUC600AAA0100011





















































































Результаты поиска

Содержание BMUC600AAA0100011

Отзывы:

Похожие инструкции для BMUC600AAA0100011

Бренды по названию

Популярные бренды

Trane BMUC600AAA0100011, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BMUC600AAA0100011

Отзывы:

Похожие инструкции для BMUC600AAA0100011

Бренды по названию

Популярные бренды