Trane BMUC600AAA0100011 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 84

background image

38

BAS-SVX45F-GB

Tracer UC600 Operation

LED Descriptions and Activities

The following table provides a description of LED activity, indicators, and troubleshooting tips.
Refer to

, for locations of the LEDs.

Note:

Points that are in an alarm state when the notification type is configured as “alarm” will
cause the power LED to flash red. If the notification type of a point is configured as “event,”
the power LED will not flash when the point is in an alarm state.

Table 11. LED identification and interpretation

LED type

LED activity

Indicates...

Troubleshooting/Notes

Power

Solid green

Normal operation

Sequence on powerup:

Illuminates

red, then flashes green, then solid green.

Solid red

Low voltage or malfunction

Blinking red

Alarm or fault is present (*

see note

)

Communication

(Link, MBUS, IMC)

TX (transmit) blinks green

Normal operation; blinks at a fixed rate when
transferring data to other devices on the link

TX LED: Regardless of connectivity, the
TX will blink as it searches for devices to
communicate with.

RX (receive) blinks yellow

Normal operation; blinks at a fixed rate when
receiving data from other devices on the link

RX on solid (yellow)

Reverse polarity is present

LED not illuminated

The controller is not detecting
communication

• Cycle the power to reestablish

communication.

• Verfiy that the controller is capable of

communicating with other devices on
the link.

• Check polarity and baud rate.

Service

Solid green

LED has been pressed and remains on until
powered down (does not affect normal
operation)

LED not illuminated

Normal operation

Binary outputs

(BO1 through BO4

Solid yellow

Relay coil energized

LED not illuminated

Relay coil de-energized or No command

Ethernet

LINK on solid (green)

Valid Ethernet connection

ACT flickers (yellow)

Data transmission and reception

«
...
36
37
38
39
40
...
»

Содержание BMUC600AAA0100011





















































































Отзывы:

Нет отзывов

Похожие инструкции для BMUC600AAA0100011

Бренд: Vacon Страницы: 64

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: Federal Signal Corporation Страницы: 60

Бренд: FASTRON. Страницы: 16

Бренд: Nedap Страницы: 20

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 19

Бренд: Eaton Страницы: 10

Бренд: Idemia Страницы: 29

SYSMAC C500-NC222-E

Бренд: Omron Страницы: 164

Бренд: IN-COMMAND Страницы: 47

Бренд: SYCLOPE Страницы: 60

Бренд: East Coast Datacom Страницы: 14

Бренд: Woodward Страницы: 32

Бренд: M-system Страницы: 5

Бренд: Satel Страницы: 7

Бренд: Consort Страницы: 4

Бренд: Broadcast Tools Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды