manualshive.com logo in svg

Toshiba Tecra M9, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra M9 Скачать руководство пользователя страница 94

2  Troubleshooting Procedures  

2.9 Optical Drive Troubleshooting

 

Procedure 2 

Connector Check and Replacement Check 

The optical drive (Super Multi drive) is connected to the system board. The connectors may 
be disconnected from the system board or may be damaged. Disassemble the computer 
following the steps described in Chapter 4, 

Replacement Procedures

 and perform the 

following checks: 

Check 1  Make sure the drive to test is firmly connected to CN1820 on the system board. 

 

If the connection is loose, reconnect firmly and repeat Procedure 1. If there is still 
an error, go to Check 2. 

Check 2  The drive may be defective or damaged. Replace the drive with a new one. If 

there is still an error, go to Check 3. 

Check 3  Replace the system board with a new one following the steps in Chapter 4, 

Replacement Procedures

. 

 

2-44

 

[CONFIDENTIAL]

 

TECRA M9 Maintenance Manual (960-631) 

Содержание Tecra M9































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды