Toshiba Tecra M9 Скачать руководство пользователя страница 180

Страница: 180 / 414

3 Tests and Diagnostics

3.24 Floppy Disk Drive Utilities

3-54

[CONFIDENTIAL]

TECRA M9 Maintenance Manual (960-631)

3.24 Floppy Disk Drive Utilities

3.24.1 Function Description

This function formats the FDD, copies the floppy disk and displays the dump list for both the
FDD and HDD.

FORMAT

NOTE

: This program is only for testing a floppy disk drive. It is different from the

Toshiba DOS FORMAT command.

This program can format a floppy disk in the following formats:

(a)

2DD: Double-sided, double-density, double-track, 96/135 TPI, MFM mode,
512 bytes, 9 sectors/track.

(b)

2HD: Double-sided, high-density, double-track, 96/135 TPI, MFM mode, 512
bytes, 18 sectors/track.

COPY

This program copies data from a source floppy disk to a target floppy disk.

DUMP

This program displays the contents of the floppy disk and the designated sectors of
the hard disk on the display.

HDD ID READ

This program reads the hard disk ID and displays hard disk information.

Содержание Tecra M9































































































































































































































































































































































































































Результаты поиска

Содержание Tecra M9

Отзывы:

Бренды по названию

Популярные бренды

Toshiba Tecra M9, Руководство по обслуживанию

Результаты поиска

Содержание Tecra M9

Отзывы:

Бренды по названию

Популярные бренды