Toshiba Tecra M9 Скачать руководство пользователя страница 161

Страница: 161 / 414

3.17 CD-ROM/DVD-ROM Test

3 Tests and Diagnostics

TECRA M9 Maintenance Manual (960-631)

[CONFIDENTIAL]

3-35

3.17 CD-ROM/DVD-ROM Test

NOTE

: For the subtest 01, 02 and 03, use the TOSHIBA CD-ROM TEST DISK TDY-01

or ABEX TEST CD-ROM TCDR-702 and DVD-ROM TEST DISK TSD-1. For the
subtest 04, use a CD-RW on the market.

Subtest 01

Sequential read

This subtest is a sequential reading of one-block units (2K bytes) of all the
logical addresses.

Subtest 02

Read specified address

This subtest reads one-block data from a specified address.

Subtest 03

Random address/data

This subtest reads one-block data and multi-block data from random addresses
200 times.

Subtest 04

RW 1point W/R/C

This subtest writes, reads and compares data at one point on a CD/RW media.

Содержание Tecra M9































































































































































































































































































































































































































Результаты поиска

Содержание Tecra M9

Отзывы:

Бренды по названию

Популярные бренды

Toshiba Tecra M9, Руководство по обслуживанию

Результаты поиска

Содержание Tecra M9

Отзывы:

Бренды по названию

Популярные бренды