Toshiba Tecra M9 Скачать руководство пользователя страница 130

Страница: 130 / 414

3 Tests and Diagnostics

3.1 The Diagnostic Test

3-4

[CONFIDENTIAL]

TECRA M9 Maintenance Manual (960-631))

3.1.2 H/W (Hardware) initial information setting tool

The H/W initial information setting tool consists of the following programs.

Initial configuration

DMI information save

DMI information recovery

System configuration display

E2PROM test (MAC/GUID/DMI)

You will need the following equipment to perform some of the programs.

The Diagnostics Disk (Main T&D)

3.1.3 Heatrun test program

The heatrun test starts automatically after the selection.

You will need the following equipment to perform this program.

The Diagnostics Disk (Main T&D)

Содержание Tecra M9































































































































































































































































































































































































































Результаты поиска

Содержание Tecra M9

Отзывы:

Бренды по названию

Популярные бренды

Toshiba Tecra M9, Руководство по обслуживанию

Результаты поиска

Содержание Tecra M9

Отзывы:

Бренды по названию

Популярные бренды