manualshive.com logo in svg

Toshiba Tecra M9, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra M9 Скачать руководство пользователя страница 287

4.16 Fingerprint sensor board 

4  Replacement Procedures 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL] 

4-53 

Installing the Fingerprint sensor board 

The following describes the procedure for installing the fingerprint sensor board. (See Figure 
4-26 and 4-27.) 

1.

 

Connect the 

fingerprint sensor cable

 to the connector on the fingerprint sensor board. 

2.

 

Stick a new 

double-sided tape

 in place and install the 

fingerprint sensor board

. 

NOTE

:  Do not reuse the removed double-sided tape. 

3.

 

Install the 

fingerprint sensor board hold plate

 while sliding it to the guides. 

4.

 

Arrange the fingerprint sensor cable and stick the 

glass tape

 in place. 

Содержание Tecra M9































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды